- 您现在的位置：买卖IC网 > Sheet目录279 > 101-0359 (Rabbit Semiconductor)KIT DEVELOPMENT BASIC RABBIT2000
2.4 Start Dynamic C
Once the BL1810 is connected as described in Section 2.3, start Dynamic C by double-click-
ing on the Dynamic C icon or by double-clicking on dcrabXXXX.exe in the Dynamic C root
directory, where XXXX are version-specific characters .
If you are using a USB port to connect your computer to the BL1810, choose Options >
Project Options and select “Use USB to Serial Converter” under the Communications
tab.
2.5 Run a Sample Program
Find the file PONG.C , which is in the Dynamic C SAMPLES folder. To run the program,
open it with the File menu (if it is not still open), compile it using the Compile menu, and
then run it by selecting Run in the Run menu. The STDIO window will open and will dis-
play a small square bouncing around in a box.
This program shows that the CPU is working.
2.5.1 Troubleshooting
If Dynamic C appears to compile the BIOS successfully, but you then receive a communi-
cation error message when you compile and load the sample program, it is possible that
your PC cannot handle the higher program-loading baud rate. Try changing the maximum
download rate to a slower baud rate as follows.
? Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications menu. Select a slower Max download baud rate.
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud
rate. Try lowering the debugging baud rate as follows.
? Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications menu. Choose a lower debug baud rate.
If there are any other problems:
? Check to make sure you are using the PROG connector, not the DIAG connector, on the
programming cable.
? Check both ends of the programming cable to ensure that they are firmly plugged into
the PC and the programming port on the BL1810.
? Ensure that the BL1810 is firmly and correctly installed in its connectors on the
Prototyping Board.
? Select a different COM port within Dynamic C. From the Options menu, select
Project Options , then select Communications . Select another COM port from the
list, then click OK. Press <Ctrl-Y> to force Dynamic C to recompile the BIOS. If
Dynamic C still reports it is unable to locate the target system, repeat the above steps until
you locate the active COM port.
14
Rabbit 2000 Development Kit
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
101-0523
KIT DEV RABBIT3000/RCM3000
101-1109
KIT EMBEDDED PLC APPLICATION
101-1147
KIT RIO PROGRAM I/O
101-606
CONN SOCKET IDC 60POS W/KEY GOLD
10113616-01531LF
CONN MOD JACK 8PORT 8/8 R/A PCB
10117863-5036010LF
CONN MOD JACK 8/8 R/A PCB
10118061-5005010LF
CONN MOD JACK 2PORT 8/8 R/A PCB
10118062-5001310LF
CONN MOD JACK 4PORT 8/8 R/A PCB
相关代理商/技术参数
101-0359-000
制造商:ITT Interconnect Solutions 功能描述:1010359000 / 101-0359-000 / Circular
10103592
制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:MICRO-USB B-TYPE REVERSE
10103592-0001LF
功能描述:USB接头 5P Quick Connect Micro USB TypeB Plug
RoHS:否 制造商:FCI 产品:USB Type A Connectors 标准:USB 3.0 端口数量: 位置/触点数量:9 型式:Female 电流额定值:1.8 A 安装风格:Through Hole 端接类型:Solder Pin 连接器类型:USB 3.0 Receptacle
10103593
制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:MICRO-USB B-TYPE MID-MOUNT
10103593-0001LF
功能描述:USB接头 5P Quick Connect Micro USB TypeB RCPT
RoHS:否 制造商:FCI 产品:USB Type A Connectors 标准:USB 3.0 端口数量: 位置/触点数量:9 型式:Female 电流额定值:1.8 A 安装风格:Through Hole 端接类型:Solder Pin 连接器类型:USB 3.0 Receptacle
10103593-0001LF
制造商:FCI 功能描述:MICRO USB B, RECEPTACLE, 5POS, SMT RT AN
10103594
制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:MICRO-USB B-TYPE RECEP.
10103594-0001LF
功能描述:USB接头 5P Quick Connect Micro USB TypeB Rcpt
RoHS:否 制造商:FCI 产品:USB Type A Connectors 标准:USB 3.0 端口数量: 位置/触点数量:9 型式:Female 电流额定值:1.8 A 安装风格:Through Hole 端接类型:Solder Pin 连接器类型:USB 3.0 Receptacle